--
-- Caution. This MIB is temporary and experimental.
-- In the future it will be removed from products, perhaps
-- with short notice, in favor of more standard or generic MIBs.
-- Application developers should not depend on long-term access
-- to this MIB.CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB
--REVISION 0.01DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Integer32,NOTIFICATION-TYPEFROM SNMPv2-SMI
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
TEXTUAL-CONVENTION,DisplayStringFROM SNMPv2-TC
ciscoExperiment
FROM CISCO-SMI
rptrGroupIndex, rptrPortGroupIndex, rptrPortIndex
FROM SNMP-REPEATER-MIB
PhysAddressFROM RFC1213-MIB;ciscoSibuStackableDualSpeedHubMIB MODULE-IDENTITYLAST-UPDATED"9810230000Z"ORGANIZATION"Cisco Systems Inc."CONTACT-INFO"Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-sibu@cisco.com"DESCRIPTION"The MIB module that extends the REPEATER-MIB to
manage CISCO low end stackable repeater products.
For the purpose of this mib, a hub is a repeater
group and stack is collection of one or more hubs
interconnected via stack bus connectors."REVISION"9810230000Z"DESCRIPTION"Initial version of this MIB module."::={ ciscoExperiment 44}ciscoSibuStackableDualSpeedHubMIBObjects OBJECTIDENTIFIER::={ ciscoSibuStackableDualSpeedHubMIB 1}cssSystem OBJECTIDENTIFIER::={ ciscoSibuStackableDualSpeedHubMIBObjects 1}cssGroup OBJECTIDENTIFIER::={ ciscoSibuStackableDualSpeedHubMIBObjects 2}
cssRepeaterPort OBJECTIDENTIFIER::={ ciscoSibuStackableDualSpeedHubMIBObjects 3}cssSwitchPort OBJECTIDENTIFIER::={ ciscoSibuStackableDualSpeedHubMIBObjects 4}HubNumber ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Represents the hub number that the system supports
for stacking. The hub number represents the order
in which a hub is stacked relative to other members
of the stack. Lowest hub number represents the top
member of the stack. This is also the number used in
the command line interface."SYNTAXInteger32(1..2147483647)-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
-- |
-- The Dual Speed Hub System Group |
-- |
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++cssSystemLinkTraps OBJECT-TYPESYNTAXINTEGER{enabled(1),-- enable linkUp/linkDown trapsdisabled(2)-- disable linkUp/linkDown traps}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates whether the stack is permitted to generate
linkUp/linkDown traps for both repeater port and
switch module's port. The stack provides only
a single global control of link traps in contrast
to per interface control provided by IF-MIB. The
value of all instances ifLinkUpDownTrapEnable is set
to TRUE (FALSE) if this object is set to enabled
(disabled). The object ifLinkUpDownTrapEnable is
read-only.
A linkUp/linkDown trap is generated whenever a port's
link STATUS or administrative status changes."DEFVAL{ enabled }::={ cssSystem 1}-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
-- |
-- The Dual Speed Hub Stack Group |
-- |
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++cssGroupTable OBJECT-TYPESYNTAXSEQUENCEOF CssGroupEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"A list of member hubs in the stack."::={ cssGroup 1}cssGroupEntry OBJECT-TYPESYNTAX CssGroupEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Configuration parameters for an individual hub.
An entry is created by default for the master unit
in the stack. A entry is created (removed) when
a hub is connected to (removed from) the stack."INDEX{ rptrGroupIndex }::={ cssGroupTable 1}
CssGroupEntry ::=SEQUENCE{
cssGroupID
HubNumber,
cssGroupType
INTEGER,
cssGroupSerialNo
DisplayString,
cssGroupBoardRevision
Integer32,
cssGroupAgentBootVersion
DisplayString,
cssGroupAgentFirmwareVersion
DisplayString,
cssGroupAgentStatus
INTEGER,
cssGroupAgentPhysAddress
PhysAddress,
cssGroupInternalPowerState
INTEGER,
cssGroupRedundantPowerState
INTEGER,
cssGroupReset
INTEGER,
cssGroupConfigDefaultReset
INTEGER,
cssGroupIsolatedState
INTEGER}cssGroupID OBJECT-TYPESYNTAX HubNumber
MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The hub identifier of unit in a stack."::={ cssGroupEntry 1}cssGroupType OBJECT-TYPESYNTAXINTEGER{cisco1538MDS(1),-- Cisco 1538M Micro Hub 10/100cisco1538UDS(2),-- Cisco 1538 Micro Hub 10/100wsC412M(3),-- FastHub 412M 10/100wsC412(4),-- FastHub 412 10/100wsC424M(5),-- FastHub 424M 10/100wsC424(6)-- FastHub 424 10/100
}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The model type of the hub unit"::={ cssGroupEntry 2}cssGroupSerialNo OBJECT-TYPESYNTAXDisplayString(SIZE(0..20))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Serial number of the hardware."::={ cssGroupEntry 4}cssGroupBoardRevision OBJECT-TYPESYNTAXInteger32(0..2147483647)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Hardware version of the repeater board."::={ cssGroupEntry 5}cssGroupAgentBootVersion OBJECT-TYPESYNTAXDisplayString(SIZE(0..8))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Returns the version number of the dual-speed hub
BOOT software residing in flash. The format is 'V1.2.3'."::={ cssGroupEntry 6}cssGroupAgentFirmwareVersion OBJECT-TYPE
SYNTAXDisplayString(SIZE(0..8))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Returns the version number of the dual-speed hub
firmware residing in flash. The format is 'V1.2.3'."::={ cssGroupEntry 7}cssGroupAgentStatus OBJECT-TYPESYNTAXINTEGER{notPresent(1),primary(2),backup(3)}MAX-ACCESSread-only
STATUScurrentDESCRIPTION"Status of this hub agent. Each stack allows only
one SNMP primary agent.
notPresent(1): The hub does not have an agent.
primary(2): The agent of this hub is a primary agent.
backup(3) : The agent of this hub is a backup agent."::={ cssGroupEntry 8}cssGroupAgentPhysAddress OBJECT-TYPESYNTAXPhysAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"MAC address of this hub's agent"::={ cssGroupEntry 9}cssGroupInternalPowerState OBJECT-TYPESYNTAXINTEGER{off(1),
on(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the state of the internal power supply.
off : The internal power supply is off.
on : The internal power supply is on."::={ cssGroupEntry 12}cssGroupRedundantPowerState OBJECT-TYPESYNTAXINTEGER{off(1),healthy(2),faulty(3)}MAX-ACCESSread-only
STATUScurrentDESCRIPTION"Indicates the state of the external/backup power
supply.
off : the switch is not connected to a redundant
power source.
healthy : a redundant power source is connected to
the switch and the power source is
operating correctly.
faulty : a redundant power source is connected to
the switch but a failure exists in the
power system."::={ cssGroupEntry 13}cssGroupReset OBJECT-TYPESYNTAXINTEGER{ noReset(1), reset(2)}MAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"Setting this object to reset(2) causes a complete
reset of both hardware and software, but does not run
the POST (Power On Self Test).
Setting this object to noReset(1) has no effect.
The switch always returns the value noReset(1) when
this object is read."DEFVAL{ noReset }::={ cssGroupEntry 14}cssGroupConfigDefaultReset OBJECT-TYPESYNTAXINTEGER{ noReset(1), reset(2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Setting this object to reset(2) causes a complete
reset of both hardware and software, but does not
run the POST (Power On Self Test). All
configuration parameters will revert to their
factory default settings.
Setting this object to noReset(1) has no effect.
The switch always returns the value noReset(1) when
this object is read."DEFVAL{ noReset }::={ cssGroupEntry 15}cssGroupIsolatedState OBJECT-TYPESYNTAXINTEGER{ isolated(1), attached(2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Setting this object to isolated(1) causes this hub
to be isolated from the back plane bus. Setting
this object to attached(2) causes this hub to be
attached to the back plane bus."
::={ cssGroupEntry 16}-- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
-- |
-- The Stackable Dual Speed Hub Port Configuration Table |
-- |
-- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++cssRepeaterPortTable OBJECT-TYPESYNTAXSEQUENCEOF CssRepeaterPortEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The list of repeater port configurations on each hub
unit."::={ cssRepeaterPort 1}cssRepeaterPortEntry OBJECT-TYPESYNTAX CssRepeaterPortEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"Configuration parameters for an individual repeater
port on a hub. The value of rptrPortIndex also
indicates the physical port number of the port in
the hub. An entry is created for each repeater port in
a hub when the hub is connected to the stack. The
corresponding entries are removed when the hub is
removed from the stack."INDEX{ rptrPortGroupIndex, rptrPortIndex}::={ cssRepeaterPortTable 1}
CssRepeaterPortEntry ::=SEQUENCE{
cssRepeaterPortName
DisplayString,
cssRepeaterPortControllerRevision
Integer32,
cssRepeaterPortSpeedAdmin
INTEGER,
cssRepeaterPortSpeedStatus
INTEGER,
cssRepeaterPortLinkStatus
INTEGER}cssRepeaterPortName OBJECT-TYPESYNTAXDisplayString(SIZE(0..20))MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"A descriptive string of up to 20 characters used
by the network administrator to name a port."::={ cssRepeaterPortEntry 1}cssRepeaterPortControllerRevision OBJECT-TYPESYNTAXInteger32(0..2147483647)MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Returns the revision number of the port controller."::={ cssRepeaterPortEntry 2}cssRepeaterPortSpeedAdmin OBJECT-TYPESYNTAXINTEGER{tenMbps(1),oneHundredMbps(2),autoNegotiate(3)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Set to tenMbps(1) to operate in 10Mbps speed mode.
Set to oneHundredMbps(2) to operate in 100Mbps speed
mode. Set to autoNegotiate(3) to allow the switch
to negotiate with the other end of the connection.
The actual operating speed of the port is given by
cssRepeaterPortSpeedStatus."DEFVAL{ autoNegotiate }::={ cssRepeaterPortEntry 3}cssRepeaterPortSpeedStatus OBJECT-TYPESYNTAXINTEGER{tenMbps(1),-- 10 Mbit/soneHundredMbps(2)-- 100 Mbit/s}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The operating speed of the port."::={ cssRepeaterPortEntry 4}cssRepeaterPortLinkStatus OBJECT-TYPE
SYNTAXINTEGER{ link(1), noLink(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The current port link status."::={ cssRepeaterPortEntry 5}-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
-- |
-- The Extension Module Switched Port Group |
-- |
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++cssSwitchPortTable OBJECT-TYPESYNTAXSEQUENCEOF CssSwitchPortEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"A list of switched ports on extension module on a each
hub unit in the stack."::={ cssSwitchPort 1}cssSwitchPortEntry OBJECT-TYPESYNTAX CssSwitchPortEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Configuration parameters for an individual switch
module port. An entry is created for each switch port
on a module is inserted into a hub in the stack.
The corresponding entries are removed when the module
is removed from the hub in the stack, or if the hub
is removed from the stack."INDEX{ rptrGroupIndex, cssSwitchPortModuleID,
cssSwitchPortPortID }
::={ cssSwitchPortTable 1}
CssSwitchPortEntry ::=SEQUENCE{
cssSwitchPortModuleID
Integer32,
cssSwitchPortPortID
Integer32,
cssSwitchPortName
DisplayString,
cssSwitchPortType
INTEGER,
cssSwitchPortControllerRevision
Integer32,
cssSwitchPortState
INTEGER,
cssSwitchPortDuplexAdmin
INTEGER,
cssSwitchPortDuplexStatus
INTEGER,
cssSwitchPortSpeedAdmin
INTEGER,
cssSwitchPortSpeedStatus
INTEGER,
cssSwitchPortLinkStatus
INTEGER
}cssSwitchPortModuleID OBJECT-TYPESYNTAXInteger32(1..2147483647)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Unique ID number of a module unit in a hub as used
in the command line interface."::={ cssSwitchPortEntry 1}cssSwitchPortPortID OBJECT-TYPESYNTAXInteger32(1..2147483647)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The unique ID identifying a port on an extension module
on a hub as used in the command line interface."
::={ cssSwitchPortEntry 2}cssSwitchPortName OBJECT-TYPESYNTAXDisplayString(SIZE(0..20))MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"A descriptive string of up to 20 characters used by the
network administrator to name a switch port."::={ cssSwitchPortEntry 3}cssSwitchPortType OBJECT-TYPESYNTAXINTEGER{wsX4001(1),-- 10/100 Tx switch module for FastHub 400wsX4002(2)-- 100BaseFx switch module for FastHub 400
}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Type of switch module in this hub."::={ cssSwitchPortEntry 4}cssSwitchPortControllerRevision OBJECT-TYPESYNTAXInteger32(0..2147483647)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The revision number of the port controller."::={ cssSwitchPortEntry 5}cssSwitchPortState OBJECT-TYPE
SYNTAXINTEGER{enabled(1),-- switch port enableddisabled(2)-- switch port disabled}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Setting this object to enabled(1) enables the port.
Setting this object to disabled(2) disables the port."DEFVAL{ enabled }::={ cssSwitchPortEntry 6}cssSwitchPortDuplexAdmin OBJECT-TYPESYNTAXINTEGER{fullDuplex(1),
halfDuplex(2),autoNegotiate(3)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Set to fullDuplex(1) to operate in full duplex mode: port
will allow simultaneous transmit and receive which can
double its bandwidth. Set to halfDuplex(2) to operate in
normal mode. Set to autoNegotiate(3) to allow the switch
to negotiate the duplex status with the other end of the
connection."DEFVAL{ autoNegotiate }::={ cssSwitchPortEntry 7}cssSwitchPortDuplexStatus OBJECT-TYPESYNTAXINTEGER{fullDuplex(1),
halfDuplex(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The operating duplex mode of the switched port."::={ cssSwitchPortEntry 8}cssSwitchPortSpeedAdmin OBJECT-TYPESYNTAXINTEGER{tenMbps(1),oneHundredMbps(2),autoNegotiate(3)}MAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"Set to tenMbps(1) to operate in 10Mbps speed mode. Set to
oneHundredMbps(2) to operate in 100Mbps speed mode. Set to
autoNegotiate(3) to allow the switch to negotiate the operating
speed with the other end of the connection.
If the value of object cssSwitchPortType is WS-X4002(2),
this object will be read-only, because FX module only
supports 100Mbps speed."DEFVAL{ autoNegotiate }::={ cssSwitchPortEntry 9}cssSwitchPortSpeedStatus OBJECT-TYPESYNTAXINTEGER{tenMbps(1),oneHundredMbps(2)}MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The operating speed of the switched port."::={ cssSwitchPortEntry 10}cssSwitchPortLinkStatus OBJECT-TYPESYNTAXINTEGER{link(1),noLink(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the link STATUS of switch port."::={ cssSwitchPortEntry 11}-- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
-- | |
-- The stackable Dual Speed Hub Switch Enterprise Specific Traps |
-- |
-- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-- NotificationsciscoSibuStackableDualSpeedHubNotifications OBJECTIDENTIFIER::={ ciscoSibuStackableDualSpeedHubMIB 2}ciscoSibuStackableDualSpeedHubNotificationsPrefix OBJECTIDENTIFIER::={ ciscoSibuStackableDualSpeedHubNotifications 0}ciscoSibuStackableDualSpeedHubRptrPortLinkChange NOTIFICATION-TYPEOBJECTS{ cssRepeaterPortLinkStatus }STATUScurrentDESCRIPTION"This trap is generated whenever the value of
cssRepeaterPortLinkStatus changes for a repeater port."
::={ ciscoSibuStackableDualSpeedHubNotificationsPrefix 1}ciscoSibuStackableDualSpeedHubSwitchPortLinkChange NOTIFICATION-TYPEOBJECTS{ cssSwitchPortLinkStatus }STATUScurrentDESCRIPTION"This trap is generated whenever the value of
cssSwitchPortLinkStatus changes for a switch port
on an extension module."::={ ciscoSibuStackableDualSpeedHubNotificationsPrefix 2}-- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
-- |
-- The Stackable Dual-Speed Ethernet Hub Enterprise Module comformance |
-- |
-- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ciscoSibuStackableDualSpeedHubMIBComformance OBJECTIDENTIFIER
::={ ciscoSibuStackableDualSpeedHubMIB 3}ciscoSibuStackableDualSpeedHubMIBCompliances OBJECTIDENTIFIER::={ ciscoSibuStackableDualSpeedHubMIBComformance 1}ciscoSibuStackableDualSpeedHubMIBGroups OBJECTIDENTIFIER::={ ciscoSibuStackableDualSpeedHubMIBComformance 2}-- compliance statementsciscoSibuStackableDualSpeedHubCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for the Cisco Stackable Dual-Speed
Hub products."MODULE-- this moduleMANDATORY-GROUPS{
ciscoSibuStackableDualSpeedHubGroup,
ciscoSibuStackableDualSpeedHubRepeaterPortGroup
}GROUP ciscoSibuStackableDualSpeedHubSwitchPortGroup
DESCRIPTION"Devices that have switched ports modules must implement
objects in this group."::={ ciscoSibuStackableDualSpeedHubMIBCompliances 1}-- group statementsciscoSibuStackableDualSpeedHubGroup OBJECT-GROUPOBJECTS{
cssSystemLinkTraps,
cssGroupID,
cssGroupType,
cssGroupSerialNo,
cssGroupBoardRevision,
cssGroupAgentBootVersion,
cssGroupAgentFirmwareVersion,
cssGroupAgentStatus,
cssGroupAgentPhysAddress,
cssGroupInternalPowerState,
cssGroupRedundantPowerState,
cssGroupReset,
cssGroupConfigDefaultReset,
cssGroupIsolatedState
}STATUScurrentDESCRIPTION"A collection of group objects for use with the Cisco
Stackable Dual-Speed Hub products."::={ ciscoSibuStackableDualSpeedHubMIBGroups 1}ciscoSibuStackableDualSpeedHubRepeaterPortGroup OBJECT-GROUPOBJECTS{
cssRepeaterPortName,
cssRepeaterPortControllerRevision,
cssRepeaterPortSpeedAdmin,
cssRepeaterPortSpeedStatus,
cssRepeaterPortLinkStatus
}STATUScurrentDESCRIPTION"A collection of repeater port objects for use
with the Cisco Stackable Dual-Speed Hub products."::={ ciscoSibuStackableDualSpeedHubMIBGroups 2}ciscoSibuStackableDualSpeedHubSwitchPortGroup OBJECT-GROUPOBJECTS{
cssSwitchPortModuleID,
cssSwitchPortPortID,
cssSwitchPortName,
cssSwitchPortType,
cssSwitchPortControllerRevision,
cssSwitchPortState,
cssSwitchPortDuplexAdmin,
cssSwitchPortDuplexStatus,
cssSwitchPortSpeedAdmin,
cssSwitchPortSpeedStatus,
cssSwitchPortLinkStatus
}STATUScurrentDESCRIPTION"A collection of switch module port objects for use with
the Cisco Stackable Dual-Speed Hub products."::={ ciscoSibuStackableDualSpeedHubMIBGroups 3}END